POOL LIGHT REPAIR: TIPS FOR A QUICK FIX
A swimming pool is a valuable asset that deserves attention and maintenance. You don't have to call a professional for pool light repairs. With expert guidance from Frank Wall, you can learn how to repair or replace your pool lights without causing any damage to yourself or your pool. Get essential advice and troubleshooting techniques for pool light repair so you can become your own pool expert. Save time and money with DIY repairs done the right way.
>>> See more Review Utilitech 196.8-in Plug-In Under Cabinet LED Strip Light at: https://band.us/band/90424574/post/24
Pool Light Repair
When water and electrical circuits come together, extra caution should be taken. Light fixtures are designed to stay dry. If there is water inside a light fixture, it means the lens seal has been broken or distorted. Chlorine and old gaskets can cause them to distort and degrade.
Therefore, if any water is present in any of the housing units, your pool light can break at any moment. It's time to save your pool lights! Always make sure to follow the following advice before attempting any pool light repairs:
Turn off the power to your pool at the main circuit breaker.
Switch off the ground fault circuit interrupter (GFCI) to ensure that no electricity is flowing through the circuits.
Press a non-contact voltage tester against your light socket when turning it on and off. This will confirm that the electricity has been shut off by detecting any presence of electricity. This device is also known as an electrical test meter and can be purchased at any hardware store for $10-$30.
Have dry towels ready.
You don't need to drain your pool for any of these repairs.
It's a good idea to regularly swim with pool goggles and inspect your pool lights for leaks.
How to Fix a Leaky Pool Light
Remove the locking screw.
Pull the light out of the pool wall and place it on the edge of the pool on a dry towel. (The cable should be long enough to do this.)
Remove the lens frame and take out the distorted or broken gasket.
Replace the old gasket with a new one.
Reassemble the housing unit, ensuring everything is completely dry.
Place the housing unit back into the pool wall.
Slide the locking screw back in place.
>>> See more Top 5 Best LED Kitchen Strip Lights Under Cabinet at: https://www.deviantart.com/ledlightsblls/status-update/Top-5-Best-LED-Kitchen-986637735
How to Fix a Loose Light Fixture
If the light fixture holding the pool light wobbles when you touch it, it means the locking screw needs to be tightened. Grab a Phillips screwdriver and pool goggles and tighten that screw!
Hold the screwdriver next to you on the edge of the pool on a dry towel.
With pool goggles on, get into the pool next to the loose fixture.
Locate the locking screw of the fixture. It's a single screw on the top of a fixture's face that secures the pool light to the wall.
Tighten the locking screw as tightly as possible.
How to Repair a Pool Light Bulb
For this pool light repair, it's good to have another person with you. One person watches the pool light as you turn the power back on. Also, purchase electrical contact grease if you can find it. It will make it much easier to remove any light bulb.
Check your switchboard. If the light still doesn't turn on, the bulb has burned out.
Unscrew the housing unit and place it on a dry towel on the edge of the pool near you.
Insert a small amount of electrical contact grease into the socket.
Remove the light bulb. Shake it next to your ear. If you hear a loose sound, it means the bulb has burned out and needs to be replaced.
Unscrew the old light bulb and place it on the dry towel.
Screw in a new light bulb.
Test the new light bulb by quickly turning on your pool's power. (This should be done as quickly as possible because new light bulbs burn out when outside of the water.) It's best if someone else watches the light while you turn on the power.
Checking for a Faulty or Tripped Switch
If you don't hear anything rattling in the light bulb, it may be a tripped switch.
Go to your switch panel. It should be in the AFS position with a red or yellow square pointing next to it.
Make sure you turn off any additional accessories you have on the same circuit.
Reset your switch by pressing it down completely and then moving it in the opposite direction to restore it. (If the switch automatically switches back on, you may need a new switch.
>>> See more Best LED Strip Lights For Under Kitchen Cabinets at: https://www.linkedin.com/posts/bestledlightstripsblls_best-led-strip-lights-for-under-kitchen-cabinets-activity-7116241239686971392-KHyS
A swimming pool is a valuable asset that deserves attention and maintenance. You don't have to call a professional for pool light repairs. With expert guidance from Frank Wall, you can learn how to repair or replace your pool lights without causing any damage to yourself or your pool. Get essential advice and troubleshooting techniques for pool light repair so you can become your own pool expert. Save time and money with DIY repairs done the right way.
>>> See more Review Utilitech 196.8-in Plug-In Under Cabinet LED Strip Light at: https://band.us/band/90424574/post/24
Pool Light Repair
When water and electrical circuits come together, extra caution should be taken. Light fixtures are designed to stay dry. If there is water inside a light fixture, it means the lens seal has been broken or distorted. Chlorine and old gaskets can cause them to distort and degrade.
Therefore, if any water is present in any of the housing units, your pool light can break at any moment. It's time to save your pool lights! Always make sure to follow the following advice before attempting any pool light repairs:
Turn off the power to your pool at the main circuit breaker.
Switch off the ground fault circuit interrupter (GFCI) to ensure that no electricity is flowing through the circuits.
Press a non-contact voltage tester against your light socket when turning it on and off. This will confirm that the electricity has been shut off by detecting any presence of electricity. This device is also known as an electrical test meter and can be purchased at any hardware store for $10-$30.
Have dry towels ready.
You don't need to drain your pool for any of these repairs.
It's a good idea to regularly swim with pool goggles and inspect your pool lights for leaks.
How to Fix a Leaky Pool Light
Remove the locking screw.
Pull the light out of the pool wall and place it on the edge of the pool on a dry towel. (The cable should be long enough to do this.)
Remove the lens frame and take out the distorted or broken gasket.
Replace the old gasket with a new one.
Reassemble the housing unit, ensuring everything is completely dry.
Place the housing unit back into the pool wall.
Slide the locking screw back in place.
>>> See more Top 5 Best LED Kitchen Strip Lights Under Cabinet at: https://www.deviantart.com/ledlightsblls/status-update/Top-5-Best-LED-Kitchen-986637735
How to Fix a Loose Light Fixture
If the light fixture holding the pool light wobbles when you touch it, it means the locking screw needs to be tightened. Grab a Phillips screwdriver and pool goggles and tighten that screw!
Hold the screwdriver next to you on the edge of the pool on a dry towel.
With pool goggles on, get into the pool next to the loose fixture.
Locate the locking screw of the fixture. It's a single screw on the top of a fixture's face that secures the pool light to the wall.
Tighten the locking screw as tightly as possible.
How to Repair a Pool Light Bulb
For this pool light repair, it's good to have another person with you. One person watches the pool light as you turn the power back on. Also, purchase electrical contact grease if you can find it. It will make it much easier to remove any light bulb.
Check your switchboard. If the light still doesn't turn on, the bulb has burned out.
Unscrew the housing unit and place it on a dry towel on the edge of the pool near you.
Insert a small amount of electrical contact grease into the socket.
Remove the light bulb. Shake it next to your ear. If you hear a loose sound, it means the bulb has burned out and needs to be replaced.
Unscrew the old light bulb and place it on the dry towel.
Screw in a new light bulb.
Test the new light bulb by quickly turning on your pool's power. (This should be done as quickly as possible because new light bulbs burn out when outside of the water.) It's best if someone else watches the light while you turn on the power.
Checking for a Faulty or Tripped Switch
If you don't hear anything rattling in the light bulb, it may be a tripped switch.
Go to your switch panel. It should be in the AFS position with a red or yellow square pointing next to it.
Make sure you turn off any additional accessories you have on the same circuit.
Reset your switch by pressing it down completely and then moving it in the opposite direction to restore it. (If the switch automatically switches back on, you may need a new switch.
>>> See more Best LED Strip Lights For Under Kitchen Cabinets at: https://www.linkedin.com/posts/bestledlightstripsblls_best-led-strip-lights-for-under-kitchen-cabinets-activity-7116241239686971392-KHyS
POOL LIGHT REPAIR: TIPS FOR A QUICK FIX
A swimming pool is a valuable asset that deserves attention and maintenance. You don't have to call a professional for pool light repairs. With expert guidance from Frank Wall, you can learn how to repair or replace your pool lights without causing any damage to yourself or your pool. Get essential advice and troubleshooting techniques for pool light repair so you can become your own pool expert. Save time and money with DIY repairs done the right way.
>>> See more Review Utilitech 196.8-in Plug-In Under Cabinet LED Strip Light at: https://band.us/band/90424574/post/24
Pool Light Repair
When water and electrical circuits come together, extra caution should be taken. Light fixtures are designed to stay dry. If there is water inside a light fixture, it means the lens seal has been broken or distorted. Chlorine and old gaskets can cause them to distort and degrade.
Therefore, if any water is present in any of the housing units, your pool light can break at any moment. It's time to save your pool lights! Always make sure to follow the following advice before attempting any pool light repairs:
Turn off the power to your pool at the main circuit breaker.
Switch off the ground fault circuit interrupter (GFCI) to ensure that no electricity is flowing through the circuits.
Press a non-contact voltage tester against your light socket when turning it on and off. This will confirm that the electricity has been shut off by detecting any presence of electricity. This device is also known as an electrical test meter and can be purchased at any hardware store for $10-$30.
Have dry towels ready.
You don't need to drain your pool for any of these repairs.
It's a good idea to regularly swim with pool goggles and inspect your pool lights for leaks.
How to Fix a Leaky Pool Light
Remove the locking screw.
Pull the light out of the pool wall and place it on the edge of the pool on a dry towel. (The cable should be long enough to do this.)
Remove the lens frame and take out the distorted or broken gasket.
Replace the old gasket with a new one.
Reassemble the housing unit, ensuring everything is completely dry.
Place the housing unit back into the pool wall.
Slide the locking screw back in place.
>>> See more Top 5 Best LED Kitchen Strip Lights Under Cabinet at: https://www.deviantart.com/ledlightsblls/status-update/Top-5-Best-LED-Kitchen-986637735
How to Fix a Loose Light Fixture
If the light fixture holding the pool light wobbles when you touch it, it means the locking screw needs to be tightened. Grab a Phillips screwdriver and pool goggles and tighten that screw!
Hold the screwdriver next to you on the edge of the pool on a dry towel.
With pool goggles on, get into the pool next to the loose fixture.
Locate the locking screw of the fixture. It's a single screw on the top of a fixture's face that secures the pool light to the wall.
Tighten the locking screw as tightly as possible.
How to Repair a Pool Light Bulb
For this pool light repair, it's good to have another person with you. One person watches the pool light as you turn the power back on. Also, purchase electrical contact grease if you can find it. It will make it much easier to remove any light bulb.
Check your switchboard. If the light still doesn't turn on, the bulb has burned out.
Unscrew the housing unit and place it on a dry towel on the edge of the pool near you.
Insert a small amount of electrical contact grease into the socket.
Remove the light bulb. Shake it next to your ear. If you hear a loose sound, it means the bulb has burned out and needs to be replaced.
Unscrew the old light bulb and place it on the dry towel.
Screw in a new light bulb.
Test the new light bulb by quickly turning on your pool's power. (This should be done as quickly as possible because new light bulbs burn out when outside of the water.) It's best if someone else watches the light while you turn on the power.
Checking for a Faulty or Tripped Switch
If you don't hear anything rattling in the light bulb, it may be a tripped switch.
Go to your switch panel. It should be in the AFS position with a red or yellow square pointing next to it.
Make sure you turn off any additional accessories you have on the same circuit.
Reset your switch by pressing it down completely and then moving it in the opposite direction to restore it. (If the switch automatically switches back on, you may need a new switch.
>>> See more Best LED Strip Lights For Under Kitchen Cabinets at: https://www.linkedin.com/posts/bestledlightstripsblls_best-led-strip-lights-for-under-kitchen-cabinets-activity-7116241239686971392-KHyS
0 Comments
0 Shares
Arabic
French
Spanish
Portuguese
Deutsch
Turkish
Dutch
Italiano
Russian
Romaian
Portuguese (Brazil)
Greek